Ball bearing for prop shaft mount. 131

[106usj]

Hello.
Ive searched ebay for this part and cant find.
Ive listened to all the comments recived from all about my drive shaft first gear  problem after reading the Haynes manual ive decided to first try the ball bearing that is in the centre prop shaft mount. One problem where the hel do i fing it.
Also can any one answer my clutch cable. question in Garage section.
Thanks very much all...
MacL.

[Thotos]

Contact Yagmur for the propshaft centre mount. He has brand new complete mounts. And while you are changing that it's worth changing the gearbox rubber mount at the rear as they get soft and allow the gearbox to move too much. As for the clutch cable, I thought all RHD 131s use the same clutch cable.

[Walezy]

Available in Poland also, if you need it just let me know and i will check the prices in local store.

[djape1977]

centre prop shaft mount is the same as for any Lada. might be easyer to find and a lot cheaper. it's usualy supplied all in one - bearing and a rubber. also any fiat will do, 124, 125, 132, argenta

[106usj]

I bought the prop shaft mount on ebay but need the ball bearing to fit in it.
I can contact Yagmur to source it or.
Walezy can you get me a price and order details  please also a price for the flexible rubber coupling or as some call it the doughnut.
Sory about the clutch cable question but im still learning in the parts dept.
Also i hope to have the new k&n filter and base plate kit mid week so if it is not raining  as usual in Scotland i will let you all know when i take the K&N on its maiden voyage.
MacL.......

[sid131]

i got a prop center mount off Yagmur & its perfect with the bearing complete.

[theredx19]

Sold a genuine one this year to a member this year last one I had

[Walezy]

The price for a complete mount is about 15 euro, it includes bearing.Rubber coupling is about 12-15euro - depends where bought.

[sid131]

they are on ebay for ?40 + post

[mirafioriman]

I think Walzey should buy a few and start listing them on ebay a good way to make a bit of a profit!

[djape1977]

i really don't see why you guys have a need to pay more than necesary for parts? that propshaft mount and bearing is widely available in eastern europe, poland included, since it was used on fso 125p and fso polonez, and on lada also. i've used those mounts from fso and from lada, whichever i got my hands on, and they were decent quality, lasting aprox 50.000kms each. prices were in the range of 15e

[eugene]

The rubber doughnut i understand is the same as fitted in Lada's(djape,correct me here if i am incorrect).Having been to eastern europe often,Walzey&djape are correct in what they state.I see a new parts venture opening here .Eugene

[sid131]

i have been trying to buy clear indicators from a lad in  Rijeka-Croatia & he says he cant post to Ireland?? so thats why we buy the parts here, its very frustrating when you cant get the stuff posted!! backward or what? sorry but thats what i think, no problem getting stuff from Yagmur in Turkey & its further also i got loads of toyota parts in Oz & Nz, can anyone over there in eastern Europe get me the clear side indicators for a 131?

[106usj]

I agree parts in uk are way over priced.They take advantage of them being quite rare over here.The european issue can be postage though.
 The Europe parts  you guys get are so much cheaper.
If Walezy and dj did buy and sell on ebay or this site it would be good .

[eugene]

I have often got various parts from Ukraine and never had any problems,but remember,watch out for the coustems,as parts obtained from outside European Union countries are subject to TAX .Eugene